Mass-Storage NAS4x Order Form

Detailed Information - Case Order Form - Complete Systems

Mass Storage NAS4x - Case Order Form
Each case includes: Fully assembled aluminum heatsink case Drive module plates for four hard drives with mounting screws and isolation pads Power button and status LED Mounting for mini-ITX motherboard One of several rear panel options Four low-profile rubber feet Hex driver for fast drive assembly

Faceplate Color

Anodizing samples in clear and black

Aluminum case and all aluminum brackets are treated by a anodizing process for corrosion protection and a long lasting uniform finish. The rear chassis and internal parts have a black finish, the faceplate can be either black or silver.

Black faceplate
Silver faceplate

Laser Etched Logo Graphics

Faceplate is laser etched with custom graphics and lettering during the anodizing process. Graphics can include company logo, button labels, system specs, and warning labels. Artwork to be provided by customer. Artwork should be in a vector format for best results. Approximate pricing:

Clear lettering on black case ($175)
Colored lettering on silver or black case ($200)

Contact A-Tech for price quote. Normally you can run several faceplates for the same minimum charge or a small nominal fee per plate. Different types of cases can be combined on order to reduce total cost.

No Logo
With custom laser etched logo graphics

Rack Mount

2U Rack Mount Faceplate

(1U case shown)

The one-piece rack mount faceplate incorporates rack mounting into the faceplate for a seamless look. The overall width of faceplate is 19". Oval mounting holes are centered at 18.312". Faceplate height is 3.50" (2U).

No rack mounting
With one-piece rack mount faceplate - add $85

Power LED
Case can be configured with a basic green power LED or a blue LED for a different look.
With Green LED With Blue LED - add $5

Machined Billet Aluminum Case Feet

Enhance the appearance of your case with these machined billet aluminum case feet.

With Standard Rubber feet

With Black Aluminum Case Feet - add $25
With Silver Aluminum Case Feet - add $25

HeatSync^® Cooling System

HeatSync^® Cooling System

(NAS-8x case shown)

This HeatSync^® Cooling system is required with the mini-ITX board. With the HeatSync^® Cooling system installed, heat from the processor is transferred into the heatsink case for dissipation to the outside air. System for the SN1800G includes mounting base for the processor and chipset (not shown in picture).

Includes:

Mounting base for processor chip
One pre-bent 6mm heat pipe
Mounting base for heatsink case
Required installation hardware

No HeatSync^® Cooling System

With HeatSync^® Cooling System for SuperMicro X7SPA-H - add $100 <--NEW!

With HeatSync^® Cooling System for VIA EPIA SN1800G motherboard- add $110

Shipping and Ordering Information

When will the case ship?

These cases are normally in stock and will ship with in 2-3 weeks depending on other options and color choice.

Quantity Discounts?

Discounts are available on orders of five or more cases. Contact A-Tech Fabrication for more information.

Mass-Storage NAS4x Case ... $549 + options

Please select options above before adding to cart. Before checking out, be sure to add any additional accessories below so that they can be shipped with your case.

Mass Storage NAS4x Case Accessories

120 Watt DC-DC Power Supply

The picoPSU-120 is the smallest snap-in 12V ATX dc-dc power supply. Plugs directly into a 20-pin ATX MB connector. 120 watts maximum output. 95% efficiency. To operate, an external AC power adapter is required, see below.

12 volts input
120 watts output
7A @ 12V
6A @ 3.3V
6A @ 5V

$49.95 each

12 Volt AC Power Adapter

External AC power adapter for use with the Mass Storage case.

100 to 240 VAC input
12 Volts Output
8.5 Amps
5mm x 2.5mm Connector

$39.00 each

Serial ATA Power Adapter Cable

Adapts 5.25" IDE power cable to dual SATA HDD power connectors. Use this cable to power two SATA drives. Two SATA power adapters cables are required in the NAS4x Case to run four drives.

$4.50 each

IDE Power Cable Splitter

Single IDE power cable to dual IDE power cable splitter. One IDE splitters is required in the NAS4x Case to run four drives.

$3.00 each