Detailed Information - Case Order Form -  Complete Systems

 HeatSync NAS-8x 2.5 Series - Case Order Form
Faceplate Color

Black case with Black faceplate

Black case with Silver faceplate
The aluminum case and all aluminum brackets are treated by an anodizing process for corrosion protection and a long lasting uniform finish. The rear portion of chassis is black anodized. The faceplate and buttons can be either black or silver.
Black case with Black faceplate
Black case with Silver faceplate
Rack Mount

2U Rack Mount Faceplate

(1U case shown)
The one-piece rack mount faceplate incorporates rack mounting into the faceplate for a seamless look. The overall width of faceplate is 19". Oval mounting holes are centered at 18.312". Faceplate height is 3.50" (2U).
No rack mounting
With one-piece rack mount faceplate - add $75
Machined Billet Aluminum Case Feet

Billet Aluminum Case Feet

 
Enhance the appearance of your case with these machined billet aluminum case feet.

 

With Standard Rubber feet

With Black Aluminum Case Feet - add $30
With Silver Aluminum Case Feet - add $30
HeatSync® Cooling System

HeatSync® Cooling System
This HeatSync® Cooling system is required with the mini-ITX board. With the HeatSync® Cooling system installed, heat from the processor is transferred into the heatsink case for dissipation to the outside air.

Includes:

  • Copper mounting base for processor
  • Two pre-bent heat pipes
  • Two aluminum clamping plates for heatsink
  • Required installation hardware

 

No HeatSync® Cooling System

With HeatSync® Cooling System for VIA EPIA SN1800G motherboard- add $120

With HeatSync® Cooling System for VIA VB8001 motherboard- add $120

With HeatSync® Cooling System for VIA EPIA EX1500G motherboard- add $120

 

Shipping and Ordering Information

When will the case ship?  

These cases are normally in stock and will ship with in 1-3 weeks depending on other options and color choice.

 

Quantity Discounts?

Discounts are available on orders of two or more cases. Contact A-Tech Fabrication for more information.

 

HeatSync® NAS-8x 2.5 Series Case ... $569 + options

Please select options above before adding to cart. Before checking out, be sure to add any additional accessories below so that they can be shipped with your case.

 

 

Case Accessories
150 Watt DC-DC Power Converter

150 Watt DC-DC Power Converter
The picoPSU-150-XT is a compact high efficiency DC-DC converter that plugs directly into a 24-pin ATX MB connector. It features a built-in P4 power cable for the motherboard and a 4-pin Molex and SATA power connector for drives and accessories.
  • Over 96% efficiency
  • 24 pin ATX connector
  • 12 volts DC input
  • 150 watts output
  • 8A @ 12V
  • 6A @ 3.3V
  • 6A @ 5V
  • MTBF = 100,000 hours at 55C deg.
$49.50 each
150 Watt 12 Volt AC Power Adapter

150 Watt 12 Volt AC Power Adapter

Adapter Cable for 150w DC converter

Fanless AC-DC power adapter. No overload fan or vent slots in sealed housing. 150 Watts output is the perfect match for the 150 watt DC-DC converter.
  • 100-240 VAC input
  • 12 Volts Output
  • 12.5 Amps, 150 watts output
  • 160 watt peak
  • 4 pin mini-din jack connector
  • Adapter cable for 150w DC converter included

 

 

 

$44.50 each
PCI Express Riser Card  
Use this angled riser to install a PCI Express x16, x8, x4, or x1 card into the PCIe slot on motherboard. Height is 1.05".

 

$29.50

Serial ATA Power Adapter Cable
Adapts 5.25" IDE power cable to dual SATA HDD power connectors. Use this cable to power two SATA drives. Four power adapter cables are required to run eight drives in the NAS-8x Case.

 

$4.50 each  (four required)

 

IDE Power Cable Splitter

Single IDE power cable to dual IDE power cable splitter. Three IDE splitters are required to run eight drives in the NAS-8x Case.

 

$3.00 each  (three required)

 

 

 

  

Home

HTPC Cases

Accessories

Antennas

 Support

Contact

 Checkout

Copyright © 2001-2010  A-Tech Fabrication Company.  All rights reserved.